Our in-house experts typically reply within one business day.
CURT
Verify Fitment
Select your vehicle to confirm this part fits.
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Select your vehicle to find the exact plug-and-play parts that fit — no cutting or splicing.
This fits: 2003-2007 Honda Accord Sedan
However you define adventure -- whether it's climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the Honda Accord (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4" receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid A-coat, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
Frame mount
Trailer hitch weight ratings are limited to vehicle manufacturer's stated capacities
Not compatible for use with vertical hanging bicycles (bike racks that require the bicycles to be hung / mounted vertically)
2003, 2004, 2005, 2006, 2007 Honda Accord Sedan Class 1 Trailer Hitch, 1-1/4" Receiver, Select Honda Accord
CURT offers a variety of high-quality trailer hitches and accessories for select vehicle models. Find the perfect fit for your towing needs at TowUniverse.
CURT, a Lippert brand, offers a complete line of towing products and is the leading manufacturer of custom-fit trailer hitches. We offer the broadest selection of custom-fit hitches, and each one is designed, welded, and coated in Wisconsin.
CURT is also a leader in flat towing products, as well as 5th wheel, gooseneck, and weight distribution hitches, ball mounts, electrical components, cargo solutions, and other towing accessories.
For everything from passenger cars and vans to full-size pickups and SUVs, CURT is 'The First Name in Towing Products®.'
Experts available to answer your questions
Call 888-634-94941 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2003 - 2007 | Honda Accord | Sedan |
The 2003-2007 Honda Accord Sedan Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11327-002) fits the following vehicles: 2003-2007 Honda Accord. Always verify your specific year, make, and model before ordering.
Yes, the 2003-2007 Honda Accord Sedan Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11327-002) is designed to fit the 2003-2007 Honda Accord.
The 2003-2007 Honda Accord Sedan Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11327-002) fits 2003-2007 Honda Accord models. The 2007 model year is the last year covered by this part number. For newer models, check for an updated version.
The 2003-2007 Honda Accord Sedan Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11327-002) Refer to the included instructions for installation details. Basic hand tools are typically all you need.
Yes, Curt 11327 is designed for 2003–2007 Honda Accord in Sedan, Coupe, and Hybrid body styles. Confirm your model year and body style match before purchasing.
The Curt 11327 is designed for 2003–2007 Honda Accord vehicles. It is compatible with Sedan, Coupe, and Hybrid body styles within this model year range.
Gross load capacity is 2,000 lbs trailer weight and 200 lbs tongue weight when used as a weight-carrying hitch. Do not exceed your vehicle manufacturer's recommended towing capacity.
The tongue weight capacity is 200 lbs when the hitch is used as a weight-carrying hitch. Always verify that your vehicle's manufacturer-recommended towing capacity is not exceeded.
The Curt 11327 is designed for use with ball mount #D-20 / 45520.
Required tools: 3/8" drive ratchet, 3/4" and 11/16" and 10mm sockets (3/8" drive), 3/8" drive torque wrench, and power drill with 5/8" bit.
The kit includes: one 7/16" fishwire, one 1/2-13 UNC grade 8 carriage bolt (1-3/4") with flange nut, two 7/16-14 UNC grade 8 carriage bolts (1-1/2" each) with flange nuts, and two 0.250 × 1.00 × 2.50" square hole spacers.
The supplied 7/16" fishwire is used to pull the 7/16" carriage bolts and spacers through the vehicle frame access holes and into the existing holes in the frame rail. This allows you to route hardware through the frame without removing the frame.
Yes. You must lower the exhaust system to access the frame rails and heat shields. Be careful not to allow mufflers to fall under their own weight. The exhaust is re-installed after hitch installation.
Be careful not to allow mufflers to fall under their own weight when lowering the exhaust system. Support the exhaust adequately to prevent injury or damage.
Yes. You must mark and drill a 5/8" hole in the heat shield 4 1/2" back from the forward-most hole on the frame rail. Mark holes and hold the hitch in position to check before drilling. Remove heat shields to drill.
A 5/8" hole must be drilled in the heat shield. The hole is located 4 1/2" back from the forward-most hole on the frame rail. Mark the hole and hold the hitch in position to verify placement before drilling. Remove the heat shield to drill.
No. The manual specifies that heat shields must be removed before drilling the 5/8" hole. After drilling, the heat shields are re-installed.
1. Lower the exhaust system carefully. 2. Mark and drill 5/8" holes in heat shields 4 1/2" back from the forward-most frame rail hole (remove heat shields first). 3. Use fishwire to pull 7/16" carriage bolts and spacers through frame access holes into existing frame holes (repeat for both sides). 4. Re-install heat shields. 5. Raise hitch over vehicle tow loop and secure with 1/2" carriage bolt and flange nut (finger tighten; support hitch so receiver tube does not rotate). 6. Rotate hitch straps to frame rails and secure with 7/16" flange nuts. 7. Torque all 7/16" fasteners to 70 lb-ft and all 1/2" fasteners to 110 lb-ft. 8. Raise exhaust and re-install rubber isolators.
Support the hitch so the receiver tube does not rotate and hit the bumper fascia. The hitch is raised into position over the vehicle tow loop and initially secured with the 1/2" carriage bolt and flange nut (finger tightened). The hitch straps are then rotated to the frame rails and secured with 7/16" flange nuts.
Fishwire is a flexible wire tool supplied with the kit. It is used to pull the 7/16" carriage bolts and spacers through the vehicle frame access holes and into the existing holes in the frame rail. This allows you to route hardware through the frame without disassembly.
Torque all 7/16" fasteners to 70 lb-ft and all 1/2" fasteners to 110 lb-ft.
All 7/16" fasteners on the Curt 11327 must be torqued to 70 lb-ft.
All 1/2" fasteners on the Curt 11327 must be torqued to 110 lb-ft.
The 1/2-13 UNC grade 8 carriage bolt is 1-3/4" long. It is used to secure the hitch to the vehicle tow loop and is torqued to 110 lb-ft.
The 7/16-14 UNC grade 8 carriage bolts are 1-1/2" long. Two are included in the kit and are torqued to 70 lb-ft each.
Two square hole spacers are included, each measuring 0.250 × 1.00 × 2.50 inches. These are routed through the frame access holes along with the 7/16" carriage bolts.
Do not exceed your vehicle manufacturer's recommended towing capacity. The Curt 11327 has a gross load capacity of 2,000 lbs trailer weight and 200 lbs tongue weight, but your vehicle's manufacturer limit may be lower and must be observed.
After installation, verify that all fasteners are tight and all structural components are sound. Periodically re-check the hitch during use to ensure fasteners remain tight and components remain in good condition.
Periodically check the receiver hitch to ensure that all fasteners are tight and that all structural components are sound. The manual does not specify an exact interval, but regular inspection before and after towing is recommended.
On Sale Today
Original price was $434.85. Current price is $327.08.You save $107.77 (25%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
FREE ShippingFREE SHIPPING
Estimated delivery Sat, Aug 15 - Tue, Aug 18
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.