Our in-house experts typically reply within one business day.
CURT
Verify Fitment
Select your vehicle to confirm this part fits.
2010 - 2011 Honda Accord Crosstour
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Complete CURT Class 1 1-1/4" trailer hitch and 4-flat custom wiring kit engineered for the 2010 - 2011 Honda Accord Crosstour. Vehicle-specific fit, plug-and-play installation, all hardware and instructions included.
This custom kit fits the following vehicles:
All Hardware and Installation Instructions Included!
However you define adventure -- whether it's climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the Honda Crosstour and Accord Crosstour (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4" receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid A-coat, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
CURT custom wiring connectors are the easiest way to outfit your vehicle with a CURT trailer wiring connection. They are built with some of the most advanced technology in the industry, and each one is custom-fitted to work with a specific make and model. Some automotive manufacturers install a special socket on the vehicle to be used for vehicle-to-trailer wiring. Although this special socket is not equipped on every vehicle, a CURT custom wiring connector -- also called a T-connector -- utilizes the socket for simple, stress-free installation. Rather than requiring you to cut, splice and solder into your vehicle's wiring system, the custom wiring connector uses a single OEM-compatible plug and instantly provides a standard, universal vehicle-to-trailer wiring connection, typically in the form a 4-way flat. All CURT custom wiring connectors are made vehicle-specific for the easiest possible installation and the best fit. This particular plug-in connector provides a 4-way flat socket and is designed to be a custom wiring option for certain years of the Honda Accord Crosstour and Acura RDX (to verify your vehicle compatibility, see application info). It comes with all necessary hardware to establish a solid connection. It also comes with a dust cover to keep the connector socket clean when not in use. To ensure long-lasting reliability, all CURT custom wiring connectors are thoroughly tested for optimal functionality. Stress is the last thing you should feel when towing a trailer -- whether you're hauling your RV to that favorite camping destination, your ATVs up to the hunting grounds or your fishing boat to the new hidden hotspot. At CURT, we think your towing equipment should add to the enjoyment of your experience, not detract from it.
CURT offers a variety of high-quality trailer hitches and accessories for select vehicle models. Find the perfect fit for your towing needs at TowUniverse.
CURT, a Lippert brand, offers a complete line of towing products and is the leading manufacturer of custom-fit trailer hitches. We offer the broadest selection of custom-fit hitches, and each one is designed, welded, and coated in Wisconsin.
CURT is also a leader in flat towing products, as well as 5th wheel, gooseneck, and weight distribution hitches, ball mounts, electrical components, cargo solutions, and other towing accessories.
For everything from passenger cars and vans to full-size pickups and SUVs, CURT is 'The First Name in Towing Products®.'
Experts available to answer your questions
Call 888-634-94941 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2010 - 2011 | Honda Accord Crosstour | — |
The 10 - 11 Honda Accord Crosstour Curt 1-1/4", Class 1 Trailer Tow Hitch + 4-flat Wiring Kit 11002 (Part #CHW-1723) fits 2010-2011 Honda Accord Crosstour models. The 2011 model year is the last year covered by this part number. For newer models, check for an updated version.
Yes, the 10 - 11 Honda Accord Crosstour Curt 1-1/4", Class 1 Trailer Tow Hitch + 4-flat Wiring Kit 11002 (Part #CHW-1723) is designed to fit the 2010-2011 Honda Accord Crosstour.
The 10 - 11 Honda Accord Crosstour Curt 1-1/4", Class 1 Trailer Tow Hitch + 4-flat Wiring Kit 11002 (Part #CHW-1723) fits the following vehicles: 2010-2011 Honda Accord Crosstour. Always verify your specific year, make, and model before ordering.
The 10 - 11 Honda Accord Crosstour Curt 1-1/4", Class 1 Trailer Tow Hitch + 4-flat Wiring Kit 11002 (Part #CHW-1723) Refer to the included instructions for installation details. Basic hand tools are typically all you need.
Yes, CURT part number 11002 is designed for Honda Accord Crosstour models from 2010 to current. It is a weight-carrying hitch with a 2,000 lbs trailer weight capacity and 200 lbs tongue weight capacity. Always verify your specific model year and body style match before purchasing.
CURT hitch 11002 is designed for use with ball mount #D-18 / 45518.
CURT hitch 11002 has a gross load capacity of 2,000 lbs trailer weight and 200 lbs tongue weight when used as a weight-carrying hitch. You must never exceed your vehicle manufacturer's recommended towing capacity.
Required tools are: 10mm, 13mm, 14mm, and 16mm sockets; 13mm, 14mm, and 16mm wrenches; 3-inch socket extension; ratchet; torque wrench; prry bar; and aviation shears. Safety glasses should be worn at all times during installation.
No. CURT hitch 11002 requires no drilling. It uses existing weld nuts on the frame rails and bumper support, and existing holes for the 7/16-inch bolts.
Yes. Heat shield trimming is required. You must remove the three bolts securing each heat shield, remove the shields from the vehicle, trim approximately 4 inches on each side as shown in the heat shield trim diagram, and then reinstall the shields.
Yes. You must remove the three rear-most rubber isolators on each side of the exhaust system to allow the mufflers to pass by the spare tire carrier. These isolators are reinstalled after the hitch installation is complete.
Two people may be required to ease installation. The manual notes that using proper tools will greatly improve the quality of the install and reduce the time required.
1. Lower the exhaust by removing the three rear-most rubber isolators on each side and gently spreading the exhaust; support the system to prevent damage. 2. Remove the existing M8 bolt from the bottom of the bumper support on each side and return it to the vehicle owner. 3. Remove the three bolts securing each heat shield, remove the shields, trim as shown, and reinstall. 4. Raise the hitch into position and loosely secure it to the frame rails using M10 hex bolts and conical toothed washers into the existing weld nuts. 5. Secure the hitch to the lower bumper support using M8 hex bolt, 5/16-inch lock washer, and 5/16-inch flat washer on both sides; insert 7/16-inch hex bolts with 3/8-inch flat washers into existing holes and secure with 7/16-inch hex flange nuts. 6. Torque all fasteners to specification. 7. Raise the exhaust into position and reinstall the rubber isolators.
Torque all M8 hardware to 23 ft-lbs, all M10 hardware to 45 ft-lbs, and all 7/16-inch hardware to 70 ft-lbs.
The kit includes: two 7/16-14 UNC hex cap screws 1-1/2 inches grade 8 (part 10-10415); two 3/8-inch flat washers (part 30-00186); two 7/16-14 UNC serrated flange nuts grade 8 (part 20-00103); two M8x1.25x35 hex cap screws class 10.9 (part 10-10393); two 5/16-inch lock washers (part 30-00219); two 5/16-inch flat washers (part 30-00195); two M10x1.25x35 hex cap screws class 10.9 (part 10-10298); and two 3/8-inch conical toothed washers (part 30-00148).
The M10 hex bolts with conical toothed washers attach to the frame rails using the existing weld nuts. They are loosely secured in step 4 and then torqued to 45 ft-lbs in step 6.
The M8 hex bolts with 5/16-inch lock washer and 5/16-inch flat washer attach to the lower bumper support on both sides of the vehicle, using the existing weld nut. They are torqued to 23 ft-lbs.
The 7/16-inch hex bolts with 3/8-inch flat washers insert into existing holes and are secured with 7/16-inch hex flange nuts. They are torqued to 70 ft-lbs.
CURT hitch 11002 has a gross load capacity of 2,000 lbs trailer weight and 200 lbs tongue weight. However, you must never exceed your vehicle manufacturer's recommended towing capacity, which may be lower than the hitch rating.
Yes. All non-trailer (wheel-less) loads applied to this hitch must be supported by auxiliary stabilizing straps. CURT recommends the use of 18050 stabilizing straps for all non-trailer loads. Failure to properly support non-trailer loads will void the product warranty.
Periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. This is a critical maintenance step to ensure safe operation.
The manual states you should periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. Regular inspection is recommended, especially after towing or hauling loads.
Yes. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
Safety glasses should be worn at all times while installing this product.
Yes, CURT 11002 fits Honda Accord Crosstour 2010 and newer. Verify your specific model year before purchasing.
2,000 lbs trailer weight and 200 lbs tongue weight. Never exceed your vehicle manufacturer's recommended towing capacity.
No drilling required. The hitch uses existing weld nuts on the frame rails and bumper support.
Yes. You must trim approximately 4 inches on each side of both heat shields. Remove, trim, and reinstall them.
10mm, 13mm, 14mm, and 16mm sockets; wrenches; 3-inch extension; ratchet; torque wrench; pry bar; aviation shears; and safety glasses.
M8 hardware: 23 ft-lbs. M10 hardware: 45 ft-lbs. 7/16-inch hardware: 70 ft-lbs.
Yes. All non-trailer loads must be supported by auxiliary stabilizing straps (CURT 18050 recommended). Failure to do so voids the warranty.
Periodically check that all fasteners are tight and all structural components are sound. This is essential for safe operation.
Yes, the Curt 56008 is designed for the Acura RDX. The connector is located behind the driver side taillight housing inside the trunk. Installation procedures vary depending on whether your vehicle has an access panel on the driver side rear trim panel; refer to the appropriate installation steps (Steps 2-A through 5-A for vehicles without the access panel, or Steps 2-B through 4-B for vehicles with the access panel).
Yes, the Curt 56008 is designed for the Honda Accord Crosstour. The connector is located on the driver side in the corner under the trim panel. Installation requires removing the cargo area cover and 10mm bolts holding the cargo tray in place, then locating and connecting to the vehicle connector. You will also need to install a 10-amp fuse in the vehicle fuse box at position 10.
The Curt 56008 has two amperage ratings: Signal Circuits are rated at 3.0 amps per side, and Tail/Running Circuits are rated at 6.0 amps total. The battery connection must be fuse-protected with a 10-amp maximum fuse. Do not exceed the product rating or the tow vehicle lamp load rating, whichever is lower, as exceeding the rating can cause loss of warranty, overheating and potential fire.
You will need a 10mm socket, a ratchet, and a panel trim removal tool. These tools are required to disconnect the battery terminal, remove cargo area covers, and remove trim panels and fasteners during installation.
Yes, you must disconnect the negative battery terminal before beginning installation. This is the first step for both Acura RDX and Honda Accord Crosstour installations and is essential for safety.
The location depends on whether your vehicle has an access panel on the driver side rear trim panel. If there is no access panel, the connector is located near the back seat under the passenger side floor spacer. If there is an access panel, the connector is located in the driver side rear trim panel and can be accessed by opening the trunk and removing the access panel. Both connectors will be similar in appearance to the custom wiring harness connector.
The vehicle connector is located on the driver side in the corner under the trim panel. To access it, open the trunk, remove the cargo area cover, and remove the 10mm bolts holding the cargo tray in place. The connector will be similar in appearance to the custom wiring harness connector.
Insert the custom wiring harness connector into the vehicle connector. Make sure the connectors are fully inserted with locking tabs in place. The connectors are designed to fit together in only one way, similar to the design of the custom wiring harness connector.
For Acura RDX vehicles, locate a flat spot inside the vehicle near the taillight and adhere the black converter box using the provided double-sided tape. For Honda Accord Crosstour vehicles, locate a flat spot outside the vehicle on the frame and adhere the black converter box using the provided double-sided tape. The location differs between vehicle types.
When in use, route the 4-flat to the center of the vehicle. When not in use, roll it up and store it in the spare tire storage area. Secure any loose wires with the provided cable ties to prevent tangling and damage.
Yes, for Honda Accord Crosstour vehicles, you must install a 10-amp fuse in the vehicle fuse box. Locate the fuse box on the driver side under the hood near the firewall, remove the fuse panel cover, and insert the provided 10-amp fuse into fuse location 10 (the trailer tow fuse position). A fuse may also be required in the vehicle fuse panel for other applications; check your vehicle owner's manual or contact the vehicle manufacturer for more information.
After connecting the wiring harness connector, reinstall all items removed during installation, reconnect the negative battery terminal, and install the provided 4-flat dust cover to help prevent corrosion. Test the connector for proper function by using a test light or connecting a properly wired trailer.
The battery connection must be fuse-protected with a 10-amp maximum fuse. Exceeding this rating can cause loss of warranty, overheating and potential fire. Do not exceed the product rating or the tow vehicle lamp load rating, whichever is lower.
Exceeding the product rating can cause loss of warranty, overheating and potential fire. The product is rated for Signal Circuits at 3.0 amps per side and Tail/Running Circuits at 6.0 amps total. Do not exceed the product rating or the tow vehicle lamp load rating, whichever is lower.
Once installed, test for proper function by using a test light or connecting a properly wired trailer. All installation steps must be followed to ensure the wiring connector will function properly.
You must remove the cargo area cover and flooring, undo the four clips holding the cargo area lid in place, remove the lid and spare tire, remove the two clips securing the passenger side panel and floor spacer, and remove the floor spacer by pushing in at the back edge and out at the front edge to clear the vehicle bracket. The vehicle connector is then located near the back seat under the passenger side floor spacer.
You must open the trunk, remove the cargo area cover, and remove the 10mm bolts holding the cargo tray in place on the driver side. The vehicle connector is then located on the driver side in the corner under the trim panel.
The Curt 56008 is designed for Acura RDX and Honda Accord Crosstour vehicles.
You need a 10mm socket, ratchet, and panel trim removal tool.
Yes, disconnect the negative battery terminal before beginning installation.
The battery connection must be fuse-protected with a 10-amp maximum fuse. Exceeding this rating can cause loss of warranty, overheating and potential fire.
Signal Circuits are rated at 3.0 amps per side, and Tail/Running Circuits are rated at 6.0 amps total.
On Sale Today
Original price was $410.90. Current price is $287.98.You save $122.92 (30%)
Free Shipping
Ships free on all orders
Authorized Dealer
Total for 4 items:
$414.57$537.49
Quick Ship
In stock and ready to ship — order now!
FREE ShippingFREE SHIPPING
Estimated delivery Sat, Aug 29 - Tue, Sep 1
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.