2012-2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Ball MountCURTOriginal price was $407.85. Current price is $304.92.In Stock
View productAsk a Question About This Product
Our in-house experts typically reply within one business day.
Our in-house experts typically reply within one business day.
CURT
Verify Fitment
Select your vehicle to confirm this part fits.
2012 - 2015 Honda Crosstour
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Select your vehicle to find the exact plug-and-play parts that fit — no cutting or splicing.
This fits: 2012-2015 Honda Crosstour All
However you define adventure -- whether it's climbing onto the back of a mountain bike, hunting from the top of a tree stand or camping with the family a long way from nowhere -- CURT class 1 hitches provide a light-duty towing receiver to help you Bring It. Each is made to fit a specific vehicle, providing easier installation, a better fit and optimal towing capacity. Custom class 1 trailer hitches are available for a variety of smaller vehicle types, including the compact car, crossover, minivan and small SUV. This particular class 1 hitch is designed to be a custom hitch for certain years of the Honda Crosstour and Accord Crosstour (to verify vehicle compatibility, see the CURT application guide at curtmfg.com). Tested in accordance with SAE J684, it offers a weight carrying capacity of 2,000 lbs. GTW and 200 lbs. TW. It is equipped with 1-1/4" receiver tube opening to accept a ball mount shank or other hitch mount. This class 1 hitch also comes with all necessary mounting hardware. With its lightweight design and smaller receiver tube size, a class 1 hitch is especially useful for adding cargo space with a hitch-mounted bike rack or cargo carrier. They can also typically be used to tow small trailers such as a utility trailer, kayak trailer or teardrop camper (never exceed the lowest weight capacity of any towing component; i.e. the vehicle, hitch, trailer, etc). Though CURT class 1 trailer hitches are only intended for light-duty towing, we apply the same principles of quality as we do to the rest of our rear mount hitches. Each class 1 hitch is made with hands-on engineering, high-strength steel and precise welding. We use a co-cured finish of liquid A-coat, inside and out, and durable black powder coat to provide a lasting defense against rust, chips and UV rays.
Trailer hitch weight ratings are limited to vehicle manufacturer's stated capacities
Not compatible for use with vertical hanging bicycles (bike racks that require the bicycles to be hung / mounted vertically)
Includes installation hardware
2012, 2013, 2014, 2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Receiver, Select Honda Crosstour, Accord
CURT offers a variety of high-quality trailer hitches and accessories for select vehicle models. Find the perfect fit for your towing needs at TowUniverse.
CURT, a Lippert brand, offers a complete line of towing products and is the leading manufacturer of custom-fit trailer hitches. We offer the broadest selection of custom-fit hitches, and each one is designed, welded, and coated in Wisconsin.
CURT is also a leader in flat towing products, as well as 5th wheel, gooseneck, and weight distribution hitches, ball mounts, electrical components, cargo solutions, and other towing accessories.
For everything from passenger cars and vans to full-size pickups and SUVs, CURT is 'The First Name in Towing Products®.'
Experts available to answer your questions
Call 888-634-94941 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2012 - 2015 | Honda Crosstour | — |
The 2012-2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11002-002) fits 2012-2015 Honda Crosstour models. The 2015 model year is the last year covered by this part number. For newer models, check for an updated version.
The 2012-2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11002-002) fits the following vehicles: 2012-2015 Honda Crosstour. Always verify your specific year, make, and model before ordering.
Yes, the 2012-2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11002-002) is designed to fit the 2012-2015 Honda Crosstour.
The 2012-2015 Honda Crosstour All Class 1 Trailer Hitch, 1-1/4" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-11002-002) Refer to the included instructions for installation details. Basic hand tools are typically all you need.
Yes, CURT part number 11002 is designed for Honda Accord Crosstour models from 2010 to current. It is a weight-carrying hitch with a 2,000 lbs trailer weight capacity and 200 lbs tongue weight capacity. Always verify your specific model year and body style match before purchasing.
CURT hitch 11002 is designed for use with ball mount #D-18 / 45518.
CURT hitch 11002 has a gross load capacity of 2,000 lbs trailer weight and 200 lbs tongue weight when used as a weight-carrying hitch. You must never exceed your vehicle manufacturer's recommended towing capacity.
Required tools are: 10mm, 13mm, 14mm, and 16mm sockets; 13mm, 14mm, and 16mm wrenches; 3-inch socket extension; ratchet; torque wrench; prry bar; and aviation shears. Safety glasses should be worn at all times during installation.
No. CURT hitch 11002 requires no drilling. It uses existing weld nuts on the frame rails and bumper support, and existing holes for the 7/16-inch bolts.
Yes. Heat shield trimming is required. You must remove the three bolts securing each heat shield, remove the shields from the vehicle, trim approximately 4 inches on each side as shown in the heat shield trim diagram, and then reinstall the shields.
Yes. You must remove the three rear-most rubber isolators on each side of the exhaust system to allow the mufflers to pass by the spare tire carrier. These isolators are reinstalled after the hitch installation is complete.
Two people may be required to ease installation. The manual notes that using proper tools will greatly improve the quality of the install and reduce the time required.
1. Lower the exhaust by removing the three rear-most rubber isolators on each side and gently spreading the exhaust; support the system to prevent damage. 2. Remove the existing M8 bolt from the bottom of the bumper support on each side and return it to the vehicle owner. 3. Remove the three bolts securing each heat shield, remove the shields, trim as shown, and reinstall. 4. Raise the hitch into position and loosely secure it to the frame rails using M10 hex bolts and conical toothed washers into the existing weld nuts. 5. Secure the hitch to the lower bumper support using M8 hex bolt, 5/16-inch lock washer, and 5/16-inch flat washer on both sides; insert 7/16-inch hex bolts with 3/8-inch flat washers into existing holes and secure with 7/16-inch hex flange nuts. 6. Torque all fasteners to specification. 7. Raise the exhaust into position and reinstall the rubber isolators.
Torque all M8 hardware to 23 ft-lbs, all M10 hardware to 45 ft-lbs, and all 7/16-inch hardware to 70 ft-lbs.
The kit includes: two 7/16-14 UNC hex cap screws 1-1/2 inches grade 8 (part 10-10415); two 3/8-inch flat washers (part 30-00186); two 7/16-14 UNC serrated flange nuts grade 8 (part 20-00103); two M8x1.25x35 hex cap screws class 10.9 (part 10-10393); two 5/16-inch lock washers (part 30-00219); two 5/16-inch flat washers (part 30-00195); two M10x1.25x35 hex cap screws class 10.9 (part 10-10298); and two 3/8-inch conical toothed washers (part 30-00148).
The M10 hex bolts with conical toothed washers attach to the frame rails using the existing weld nuts. They are loosely secured in step 4 and then torqued to 45 ft-lbs in step 6.
The M8 hex bolts with 5/16-inch lock washer and 5/16-inch flat washer attach to the lower bumper support on both sides of the vehicle, using the existing weld nut. They are torqued to 23 ft-lbs.
The 7/16-inch hex bolts with 3/8-inch flat washers insert into existing holes and are secured with 7/16-inch hex flange nuts. They are torqued to 70 ft-lbs.
CURT hitch 11002 has a gross load capacity of 2,000 lbs trailer weight and 200 lbs tongue weight. However, you must never exceed your vehicle manufacturer's recommended towing capacity, which may be lower than the hitch rating.
Yes. All non-trailer (wheel-less) loads applied to this hitch must be supported by auxiliary stabilizing straps. CURT recommends the use of 18050 stabilizing straps for all non-trailer loads. Failure to properly support non-trailer loads will void the product warranty.
Periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. This is a critical maintenance step to ensure safe operation.
The manual states you should periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. Regular inspection is recommended, especially after towing or hauling loads.
Yes. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
Safety glasses should be worn at all times while installing this product.
Yes, CURT 11002 fits Honda Accord Crosstour 2010 and newer. Verify your specific model year before purchasing.
2,000 lbs trailer weight and 200 lbs tongue weight. Never exceed your vehicle manufacturer's recommended towing capacity.
No drilling required. The hitch uses existing weld nuts on the frame rails and bumper support.
Yes. You must trim approximately 4 inches on each side of both heat shields. Remove, trim, and reinstall them.
10mm, 13mm, 14mm, and 16mm sockets; wrenches; 3-inch extension; ratchet; torque wrench; pry bar; aviation shears; and safety glasses.
M8 hardware: 23 ft-lbs. M10 hardware: 45 ft-lbs. 7/16-inch hardware: 70 ft-lbs.
Yes. All non-trailer loads must be supported by auxiliary stabilizing straps (CURT 18050 recommended). Failure to do so voids the warranty.
Periodically check that all fasteners are tight and all structural components are sound. This is essential for safe operation.
On Sale Today
Original price was $410.85. Current price is $311.08.You save $99.77 (24%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
FREE ShippingFREE SHIPPING
Estimated delivery Sat, Aug 15 - Tue, Aug 18
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.