Our in-house experts typically reply within one business day.
CURT
Verify Fitment
Select your vehicle to confirm this part fits.
2022 - 2025 BMW iX
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Select your vehicle to find the exact plug-and-play parts that fit — no cutting or splicing.
This fits: 2022-2025 BMW iX All
This CURT hitch is an accessory mount, ideal for adding a cargo carrier or bike rack onto your vehicle. It is made for vehicle-specific mounting. This particular kit fits certain years of the BMW iX (see application info to verify vehicle compatibility). It provides a tongue weight capacity of 150 lbs. (NOTE: Never exceed the lowest-rated towing component). This hitch has a 2" receiver tube and is tested in accordance with SAE J684 for safety.
Weight ratings are limited to vehicle manufacturer's stated capacities
Includes installation hardware
2022, 2023, 2024, 2025 BMW iX All Hitch Accessory Mount, 2" Receiver, Select BMW iX
CURT offers a variety of high-quality trailer hitches and accessories for select vehicle models. Find the perfect fit for your towing needs at TowUniverse.
CURT, a Lippert brand, offers a complete line of towing products and is the leading manufacturer of custom-fit trailer hitches. We offer the broadest selection of custom-fit hitches, and each one is designed, welded, and coated in Wisconsin.
CURT is also a leader in flat towing products, as well as 5th wheel, gooseneck, and weight distribution hitches, ball mounts, electrical components, cargo solutions, and other towing accessories.
For everything from passenger cars and vans to full-size pickups and SUVs, CURT is 'The First Name in Towing Products®.'
Experts available to answer your questions
Call 888-634-9494Lifetime
1 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2022 - 2025 | BMW iX | — |
The 2022-2025 BMW iX All Hitch Accessory Mount, 2" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-13532-001) fits the following vehicles: 2022-2025 BMW iX. Always verify your specific year, make, and model before ordering.
Yes, the 2022-2025 BMW iX All Hitch Accessory Mount, 2" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-13532-001) is designed to fit the 2022-2025 BMW iX.
The 2022-2025 BMW iX All Hitch Accessory Mount, 2" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-13532-001) fits 2022-2025 BMW iX models. The 2025 model year is the last year covered by this part number. For newer models, check for an updated version.
The 2022-2025 BMW iX All Hitch Accessory Mount, 2" Receiver + 2" Ball + 1-7/8" Ball Kit (Part #CHD-13532-001) Refer to the included instructions for installation details. Basic hand tools are typically all you need.
The tongue weight capacity is 150 lbs.
No. The manual explicitly states this product is 'Not intended for towing use.' You must never exceed your vehicle manufacturer's recommended towing capacity.
The manual does not specify the vehicle make, model, or year compatibility. Contact CURT product support at 877-287-8634 or visit curtmfg.com to confirm fitment for your specific vehicle.
Required tools are: ratchet, torque wrench, 8mm socket, 12mm socket, 15mm socket, 3/4" socket, 3" socket extension, tape measure, rotary tool with cut-off wheel, and tape. A tools reference guide is available at curtmfg.com/trailer-hitch-installation.
The kit includes: 1 accessory mount, 1 driver-side mounting bracket, 1 passenger-side mounting bracket, 4 carriage bolts (1/2"), 4 serrated-flange nuts (1/2"), 6 hex nuts (M12), 6 flat washers (1/2"), and 6 conical-toothed washers (1/2").
Yes. You must temporarily remove four rear underbody panels. Remove them in this order: the forward-most panel first, then the middle panel, and finally the two outer panels. All panels are reinstalled after final torque in Step 6.
Yes. You must trim the lower bumper panel. The manual provides a trim diagram showing cuts of 3-1/4", 2-3/8", and 3" for reference. Use a rotary tool with a cut-off wheel to make these cuts.
Yes. In Step 2, clean the threads of the two inner-most bumper beam studs and the top stud on the outside of each bumper beam support. If there is heavy debris in the weldnuts, use a wire brush or spray lubricant or compressed air into the hole. Take care not to damage the threads.
1. Remove four rear underbody panels (Step 1). 2. Clean bumper beam stud threads and insert flat washers over six cleaned studs (Step 2). 3. Raise driver and passenger-side mounting plates into position and loosely secure with conical-toothed washers and M12 hex nuts (Step 3). 4. Trim lower bumper panel (Step 4). 5. Raise the hitch, center it behind the bumper cover, rotate the receiver tube into position, and secure with 1/2" carriage bolts and serrated flange nuts (Step 5). 6. Torque all fasteners and reinstall panels (Step 6).
The mounting brackets should be loosely secured in Step 3 with conical-toothed washers and M12 hex nuts. They are fully tightened only in Step 6 after the hitch is centered and the carriage bolts are installed.
The manual does not mention drilling. The installation uses existing bumper beam studs and weldnuts in the vehicle frame. Trimming of the lower bumper fascia is required, but no drilling is specified.
Torque all 1/2" fasteners (carriage bolts and serrated flange nuts) to 90 ft-lbs. Torque all M12 hardware (hex nuts) to 82 ft-lbs. These torques are applied in Step 6 after the hitch is centered and all components are in final position.
The manual includes a diagram showing conical-toothed washer orientation on the hitch side plate. The washers are used under the M12 hex nuts on the mounting brackets. Refer to the 'Conical Toothed Washer Orientation' diagram on page 2 for the correct placement.
Safety glasses should be worn at all times while installing this product. Never exceed your vehicle manufacturer's recommended towing capacity. Before beginning installation, read all instructions thoroughly. Proper tools will improve the quality of installation and reduce the time required.
Periodic inspection of the trailer hitch should be performed to ensure all mounting hardware remains tight and structural components are secure. The manual recommends referring to specified torque specifications when securing hardware to help prevent damage to the product or vehicle.
The manual does not specify vehicle compatibility. Contact CURT at 877-287-8634 or visit curtmfg.com to confirm fitment for your specific make, model, and year.
You need a ratchet, torque wrench, 8mm/12mm/15mm/3/4" sockets, 3" socket extension, tape measure, rotary tool with cut-off wheel, and tape. A full tools reference guide is at curtmfg.com/trailer-hitch-installation.
Yes. You must temporarily remove four rear underbody panels and trim the lower bumper fascia using the provided trim diagram (cuts of 3-1/4", 2-3/8", and 3"). Panels are reinstalled after final torque.
Torque all 1/2" fasteners to 90 ft-lbs and all M12 hardware to 82 ft-lbs. Apply these torques in Step 6 after the hitch is centered and all components are in final position.
The product is not intended for towing use. Never exceed your vehicle manufacturer's recommended towing capacity. Wear safety glasses during installation.
Perform periodic inspection to ensure all mounting hardware remains tight and structural components are secure. Refer to the torque specifications (90 ft-lbs for 1/2" fasteners, 82 ft-lbs for M12 hardware) when checking tightness.
On Sale Today
Original price was $488.85. Current price is $360.71.You save $128.14 (26%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
FREE ShippingFREE SHIPPING
Estimated delivery Wed, Sep 16 - Sat, Sep 19
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.
