Our in-house experts typically reply within one business day.
CURT
Verify Fitment
Select your vehicle to confirm this part fits.
2011 - 2014 Chrysler 200
Confirmed to Fit
2011 - 2014 Dodge Avenger
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Select your vehicle to find the exact plug-and-play parts that fit — no cutting or splicing.
Trailer hitch weight ratings are limited to vehicle manufacturer's stated capacities
Includes ball mount #45522, installation hardware, pin & clip
Trailer ball sold separately
Includes ball mount #45522, installation hardware, pin & clip
Warranty: Limited Lifetime Warranty (One-Year Finish, One-Year Parts)
Main Body Shape: Square
Receiver Tube Size (Inches): 1-1/4 IN
Finish: GLOSS BLACK POWDER COAT
WC / TW (Pounds): 200 LB / 2,000 LB
Weight Carrying Capacity (Pounds): 2,000 LB
WC Tongue Weight (Pounds): 200 LB
Installation Difficulty: Novice
Installation Time Exact (Minutes): 30
Connect to your lifestyle with a custom hitch receiver from CURT. All of our custom hitches are designed for a vehicle-specific fit, manufactured with pride, finished for industry-leading rust resistance and tested to rigorous SAE J684 standards for safety. This class 1 trailer hitch and ball mount combination is designed for a custom fit on select years of the Chrysler 200 and Dodge Avenger (see application info to verify fitment). The hitch integrates with the vehicle's frame and provides a useful and dependable 1-1/4" x 1-1/4" receiver. The receiver is perfect for attaching the included ball mount and towing a small trailer, or for adding cargo space with a hitch-mounted cargo carrier, bike rack or other accessory. This particular class 1 hitch is rated for 2,000 pounds gross trailer weight and 200 pounds tongue weight (never exceed the lowest-rated towing component). The ball mount included with this trailer hitch quickly and easily installs into the hitch receiver and has a 3/4" trailer ball hole (trailer ball not included). It can be mounted in the rise or drop position to promote level towing. Like all CURT custom hitches, this class 1 hitch is protected with our co-cured finishing process. It is descaled for a smooth surface, immersed in liquid A-coat for rust resistance inside and out, covered with a durable black powder coat and finally co-cured for an industry-leading rust, chip and UV-resistant shield. No matter where you're headed or which season of the year you?re towing in, this CURT hitch is equipped for long-lasting resilience to the elements. It features an open-back receiver for easy cleaning, and it comes with all the hardware necessary for the installation.
CURT offers a variety of high-quality trailer hitches and accessories for select vehicle models. Find the perfect fit for your towing needs at TowUniverse.
CURT, a Lippert brand, offers a complete line of towing products and is the leading manufacturer of custom-fit trailer hitches. We offer the broadest selection of custom-fit hitches, and each one is designed, welded, and coated in Wisconsin.
CURT is also a leader in flat towing products, as well as 5th wheel, gooseneck, and weight distribution hitches, ball mounts, electrical components, cargo solutions, and other towing accessories.
For everything from passenger cars and vans to full-size pickups and SUVs, CURT is 'The First Name in Towing Products®.'
Experts available to answer your questions
Call 888-634-94942 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2011 - 2014 | Chrysler 200 | No Drilling Required Installation Time: 30-60 minutes Visibility: Exposed |
| 2011 - 2014 | Dodge Avenger | No Drilling Required Installation Time: 30-60 minutes Visibility: Exposed |
The CURT 111333 Class 1 Trailer Hitch with Ball Mount, 1-1/4-In Receiver, Fits Select Dodge Avenger, Chrysler 200 (Part #BKDK111333) fits the following vehicles: 2011-2014 Chrysler 200; 2011-2014 Dodge Avenger. Always verify your specific year, make, and model before ordering.
Yes, the CURT 111333 Class 1 Trailer Hitch with Ball Mount, 1-1/4-In Receiver, Fits Select Dodge Avenger, Chrysler 200 (Part #BKDK111333) is designed to fit the 2011-2014 Chrysler 200.
The CURT 111333 Class 1 Trailer Hitch with Ball Mount, 1-1/4-In Receiver, Fits Select Dodge Avenger, Chrysler 200 (Part #BKDK111333) fits 2011-2014 Chrysler 200 models. The 2014 model year is the last year covered by this part number. For newer models, check for an updated version.
The CURT 111333 Class 1 Trailer Hitch with Ball Mount, 1-1/4-In Receiver, Fits Select Dodge Avenger, Chrysler 200 (Part #BKDK111333) Drilling is not required for installation. Typical installation time is 30-60 minutes. Basic hand tools are typically all you need.
Yes, CURT part number 11133 is designed for Chrysler 200, 200 Hard Top Convertible, and Dodge Avenger models from 2011 to current year. Before purchasing, verify your vehicle matches one of these models and year range.
Yes, CURT part number 11133 is designed for Dodge Avenger models from 2011 to current year. Before purchasing, verify your vehicle year falls within this range.
The CURT 11133 is rated for a maximum trailer weight of 2,000 lbs and tongue weight of 200 lbs when used as a weight-carrying hitch. However, you must never exceed your vehicle manufacturer's recommended towing capacity, which may be lower than the hitch rating.
You will need: a ratchet, 3/4" socket, 3/4" boxed-end wrench, a torque wrench, and a pry bar. The manual notes that using proper tools will greatly improve the quality of the installation and reduce the time required.
No, drilling is not required. The CURT 11133 uses fishwire hardware to insert fasteners through existing access holes in the frame rails, so no drilling or permanent modifications to the vehicle are needed.
Yes, if your vehicle has dual exhaust, you must lower the exhaust before installation. Remove the four rear-most rubber isolators from the exhaust. Wire may be used to hold the exhaust to prevent damage if it is lowered too far. This step is required only for dual exhaust vehicles.
Fishwire is used to guide fasteners through the frame rail access holes. You fishwire the 1/2" carriage bolt and CM-SP12 spacer into position through the access hole in each frame rail. The manual instructs to leave fishwires attached to the hardware to prevent loss inside the frame. Detailed fishwire technique diagrams are shown in the installation walkthrough section.
All 1/2" hardware must be torqued to 110 ft-lbs. This includes the hex bolts, carriage bolts, and flange nuts. Use a torque wrench to ensure proper tightening.
The CURT 11133 includes: (2) 1/2"-13 x 4 1/2" hex bolts, (2) .188 x 1.50 x 3.00" round hole spacers (CM-SP34), (2) 1/2"-13 x 1 3/4" carriage bolts, (2) .250 x 1.00 x 2.00" square hole spacers (CM-SP12), (4) 1/2" hex flange nuts (HFN 1213), and (2) 1/2" fishwires. All fasteners and spacers needed for installation are included.
The CURT 11133 is designed for use with ballmount #45522. The manual does not indicate whether the ballmount is included with the hitch or must be purchased separately. Contact CURT technical support at 800.798.0813 or visit www.curtmfg.com for ballmount availability and ordering information.
Yes, Euro mount options are available: #45591 (1 7/8" ball) and #45592 (2" ball). However, the manual does not specify whether these are included with the hitch or must be purchased separately. Contact CURT technical support at 800.798.0813 or visit www.curtmfg.com for more information.
Safety glasses must be worn at all times while installing this product. The manual also recommends that 2 people may be required to ease installation. Read all instructions thoroughly before beginning installation.
All non-trailer (wheel-less) loads applied to the CURT 11133 must be supported by 18050 stabilizing straps. Failure to properly support non-trailer loads will void the product warranty. CURT recommends the use of 18050 stabilizing straps for all non-trailer loads. See the CURT catalog or visit www.curtmfg.com for further information.
Periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. This ongoing maintenance is critical to safe operation. The manual emphasizes this check should be performed regularly, not just after initial installation.
The manual instructs to periodically check the receiver hitch to ensure all fasteners are tight and all structural components are sound. While a specific interval is not provided, regular inspection before towing is recommended to maintain safe operation and warranty coverage.
CURT Manufacturing Inc. warrants the product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT may repair or replace it at their option when returned prepaid with proof of purchase. Warranty is voided by alteration, misuse, or improper installation. CURT's liability is limited to repair or replacement and excludes incidental or consequential loss or damage.
Yes, the CURT 11133 fits Chrysler 200, 200 Hard Top Convertible, and Dodge Avenger models from 2011 to current year.
No, no drilling is required. The hitch uses fishwire hardware to insert fasteners through existing frame rail access holes.
You need a ratchet, 3/4" socket, 3/4" wrench, torque wrench, and pry bar. All hardware is included.
All 1/2" hardware must be torqued to 110 ft-lbs.
The hitch is rated for 2,000 lbs trailer weight and 200 lbs tongue weight, but you must not exceed your vehicle manufacturer's recommended towing capacity.
Safety glasses must be worn at all times during installation. Two people may be required to ease installation.
Only if your vehicle has dual exhaust. Remove the four rear-most rubber isolators to lower the exhaust before installation.
On Sale Today
Original price was $365.95. Current price is $247.99.You save $117.96 (32%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
Shipping from Eau Claire, WIFREE SHIPPING
Estimated delivery Thu, Sep 10 - Sat, Sep 12
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
Total for 5 items:
$398.57$516.53
No reviews have been added for this product.