Our in-house experts typically reply within one business day.
ARIES
Verify Fitment
Select your vehicle to confirm this part fits.
This bumper is winch-ready, but the winch is sold separately. Pick one rated for your vehicle — check the bumper’s winch capacity and mounting bolt pattern in the specs.
2007 - 2017 Jeep Wrangler
Confirmed to Fit
2018 Jeep Wrangler JK
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Includes center section #2081001, corners #2081205 and mounting hardware
Models with factory steel front bumper will require the purchase of aftermarket fog lights (not included)
Warranty: Limited Lifetime Warranty (Five-Year Finish, One-Year Parts)
Finish: TEXTURED BLACK POWDER COAT
Material: Blank
Bumper Location: Front
The ARIES TrailChaser Jeep bumper is unlike any other bumper for the Jeep Wrangler JK because it features a modular design. With a variety of options to choose from, you can select the perfect configuration to match the style of your Jeep Wrangler. All TrailChaser bumpers are also compatible with a variety of accessories, including LED lights, D-rings, tow hooks and a winch. This particular TrailChaser bumper comes with a center section and corner end caps with flush-mount LED lights. It is constructed from T6 aluminum alloy to be strong, lightweight and rust-free, and has a unique, textured black powder coat finish for maximum corrosion resistance. It is also available in high-strength, powder-coated steel. The bumper center section features a standard 22-1/2" x 7-3/4" winch housing and is compatible with the ARIES winch adapter #2072100 for larger winches. It provides cutouts for lights and has pre-drilled holes for D-rings #2081300 and tow hooks #15600TW. The bumper corners offer a professional finishing touch with their integrated, flush-mount LED lights. The 2" square work lights put out 2,200 lumens each and feature a flood beam pattern. They are made with grade-A LED chips, rust-free aluminum construction, an IP68-standard breather and dual heat sinks. They are also thoroughly tested and come with a waterproof wiring harness for easy installation. All ARIES TrailChaser bumpers install using pre-existing factory mounting points for fast, easy installation with no drilling required.
Explore ARIES products at TowUniverse for top-tier grille guards, side bars, nerf bars, headache racks, and more. Upgrade your vehicle with ARIES today!
ARIES is a fast-paced marketer and innovator of truck, Jeep, SUV and CUV accessories. From automotive enthusiasts to professional builders, our products are built for the champions of individualism, innovation and attitude.
We offer the perfect combination of unique style and durable construction, specializing in custom-fit grille guards, bull bars, side bars and running boards, as well as Jeep Wrangler and Jeep Gladiator accessories.
ARIES products are made vehicle-specific for a custom fit, and they are available for a wide variety of makes and models sold in North America.
Experts available to answer your questions
Call 888-634-9494Limited Lifetime Warranty (Five-Year Finish, One-Year Parts)
2 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2007 - 2017 | Jeep Wrangler | — |
| 2018 | Jeep Wrangler JK | — |
The ARIES 2082044 TrailChaser Black Aluminum Front Bumper with LED Lights and Winch Mount, Select Jeep Wrangler JK (Part #BBDR2082044) fits the following vehicles: 2007-2017 Jeep Wrangler; 2018 Jeep Wrangler JK. Always verify your specific year, make, and model before ordering.
Yes, the ARIES 2082044 TrailChaser Black Aluminum Front Bumper with LED Lights and Winch Mount, Select Jeep Wrangler JK (Part #BBDR2082044) is designed to fit the 2007-2017 Jeep Wrangler.
The ARIES 2082044 TrailChaser Black Aluminum Front Bumper with LED Lights and Winch Mount, Select Jeep Wrangler JK (Part #BBDR2082044) fits 2007-2017 Jeep Wrangler models. The 2018 model year is the last year covered by this part number. For newer models, check for an updated version.
The ARIES 2082044 TrailChaser Black Aluminum Front Bumper with LED Lights and Winch Mount, Select Jeep Wrangler JK (Part #BBDR2082044) Refer to the included instructions for installation details. Basic hand tools are typically all you need.
The center section includes: 1 TrailChaser™ center section, 6 button head bolts (M4), 6 nylock nuts (M4), 4 flat washers (M4), 2 hex bolts (M6 x 20mm), 2 flat washers (M6), 3 nylock nuts (M6), 8 hex bolts (M12 x 40mm), 16 flat washers (M12 x 24mm), 8 lock washers (M12), 8 nuts (M12), and 1 Allen wrench (3mm). Additional hardware is supplied depending on the configuration purchased (side extensions, brush guards, and LED lights).
ARIES offers 20 TrailChaser™ front bumper kits in aluminum and steel versions. Kits vary by: center section (2081001 aluminum or 2081000 steel), side extension style (side extension or corner), side guard style (angular or round), and whether LED lights and guards are included. All kits are finished with textured black powder coat. Refer to the configuration tables on pages 2–3 for specific kit numbers and their included components.
No. LED lights are included only with specific kits. Kits with corner side extensions (2081205 aluminum or 2081200 steel) include LED lights. Kits with side extension style (2081201 aluminum or 2081204 steel) do not include LED lights. Kits with corner style 2081207 aluminum or 2081206 steel are not compatible with LED lights. Check your kit number on pages 2–3 to confirm LED compatibility.
Two brush guard styles are available: angular (part 2081101 aluminum or 2081100 steel) and round (part 2081254/2081250 aluminum/steel for center and sides, or 2081255/2081252 aluminum/steel for center only). Some kits include guards, some offer center-only guards, and some kits with corner side extensions (2081207 aluminum or 2081206 steel) are not compatible with any guards. Check your kit number on pages 2–3 to confirm what guards are included or compatible.
Required tools are: ratchet, socket set, socket extension, box wrench set, Phillips screwdriver, flathead screwdriver, Allen wrench set, cut-off tool, and level. A 3mm Allen wrench is provided with the center section. You will also need an 18mm socket for factory bumper removal, a 16mm socket and wrench for tightening side extensions and brush guards, a 10mm socket for vacuum pump relocation, and a 7mm socket for fog light installation.
Yes. A cut-off tool is required to remove the front post bracket from the factory bumper mount location to allow clearance for the winch receiver plate. This step is performed during bumper installation (Step 2 of section 4).
Yes. The manual states 'with help' when lifting the bumper into place over the pre-mounted bolts in the factory bumper mount locations (Step 4 of section 4). At least one additional person is recommended.
The installation is rated as Moderate difficulty.
Factory bumper removal involves six steps: (1) Remove four plastic push pins holding the air dam and pry off fasteners holding brackets to the frame; (2) Disconnect fog light wiring harness and unclip from bumper cover; (3) Remove two fasteners holding frame cover on top of bumper with Phillips screwdriver; (4) Slide cover left to expose driver side bolts, remove four nuts with 18mm socket, repeat on passenger side; (5) Carefully lift bumper from frame and set on flat work surface; (6) Remove stock fog lights for reuse in new bumper.
No. Vacuum pump relocation is required only for 2012 models and later. For these vehicles, the vacuum pump on the driver side must be moved to accommodate the new bumper. The rear bolt is loosened and the front bolt is fully removed, then the pump is swung toward the rear of the vehicle and the rear bolt is snugged (not fully tightened).
The front post bracket is the factory bracket that originally held the front post in place on the bumper mount. It must be removed to allow clearance for the winch receiver plate. It is removed using a cut-off tool during bumper installation (Step 2 of section 4).
1. Set the new center section on a flat work surface. 2. Lift the bumper side into place and insert a 10mm hex bolt with locking and flat washer. 3. Secure the bolt with a second flat washer and hex nut. 4. Repeat for all three attachment points on the first side, snugging hardware but not tightening. 5. Repeat steps 1–4 on the opposite side. 6. With both extensions loosely installed, check that bumper corners match up and adjust if necessary. 7. Fully tighten all hardware with a 16mm socket and wrench.
1. Set side extensions on flat work surface. 2. Insert rubber gasket and LED light into place. 3. Secure four LED light attachment points with M6 socket cap screw, flat washer, and nylock nut at each point. 4. Tighten all hardware and repeat for second side extension and light. 5. Set center section on flat work surface. 6. Lift side extension into place and insert M10 hex bolt, lock washer, and flat washer. 7. Secure bolt with second flat washer and hex nut. 8. Repeat for all three attachment points, snugging hardware but not fully tightening. 9. Repeat on opposite side. 10. With both extensions loosely installed, check bumper corners match up, adjust if necessary, and fully tighten all hardware with 16mm socket and wrench.
1. Place cover plate on top of brush guard. 2. Insert M6 button head cap screw with flat washer and secure with nylock nut. 3. Repeat for all six attachment points. 4. Adjust if necessary and fully tighten all hardware with Allen wrench. 5. Place center section on flat work surface. 6. Lift brush guard into place and insert M10 hex bolt with locking and flat washer. 7. Secure bolt with second flat washer and hex nut. 8. Repeat for all four attachment points. 9. Adjust if necessary and fully tighten all hardware with 16mm socket and wrench.
1. If installing side brush guards, attach the two side guards with provided M10 hex bolts, lock washers, and flat washers. Align and fully tighten hardware with 16mm socket. 2. Finalize installation by attaching center brush guard with two M10 hex bolts, lock washers, and flat washers. 3. Ensure guard(s) are aligned properly and fully tighten hardware with 16mm socket. If attaching center guard only, skip to step 2.
1. For 2012 models and later, loosen rear bolt and fully remove front bolt of vacuum pump with 10mm socket, swing pump toward rear, and snug rear bolt. 2. Remove front post bracket using cut-off tool. 3. Insert fog lights into new bumper with three attachment points each; secure with M4 socket cap screw, flat washer, flat washer, and nylock nut; tighten with 7mm socket and Allen wrench. 4. With help, lift bumper into place over pre-mounted 12mm bolts in factory bumper mount locations. 5. Insert M12 hex bolt with flat washer behind bumper bracket and secure with flat and lock washer and hex nut; snug all hardware but do not fully tighten. 6. Reattach fog lights and wire harness to bumper. 7. Place vacuum pump threaded bolt through tab on bumper and attach with M6 nylock nut. 8. Check bumper is level, adjust if necessary, and fully tighten all hardware.
The number of mounting points varies by year. The manual states 'Depending on the year of the Jeep, there may be as few as two mounting points to attach to.' The example shown has three per side. Consult your vehicle's documentation or contact ARIES Automotive at 877-287-8634 for your specific year.
The manual does not indicate that drilling is required. However, a cut-off tool is required to remove the front post bracket from the factory bumper mount location. This is a permanent modification to the factory bracket.
Torque specifications are: M6 bolt = 7 ft-lbs, M8 bolt = 16 ft-lbs, M10 bolt = 33 ft-lbs, M12 bolt = 58 ft-lbs. Use these settings unless otherwise noted in the installation instructions.
A 16mm socket and wrench are required to fully tighten all hardware on side extensions and brush guards.
An 18mm socket is required to remove the four nuts holding the bolts onto the bumper frame on each side during factory bumper removal.
A 10mm socket is required to loosen the rear bolt and fully remove the front bolt of the vacuum pump during relocation for 2012 models and later.
A 7mm socket is required to tighten the M4 socket cap screws securing the fog lights into the new bumper. The provided 3mm Allen wrench is also used.
Periodic inspections should be performed to ensure all mounting hardware remains tight. To protect the product, wax after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For polished, gloss, and other smooth finishes, polish may be used to clear small scratches and scuffs. Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive cleaners, abrasive pads, wire brushes, or other similar products that may damage the finish.
Do not use: any type of polish or wax that may contain abrasives, dish detergent, abrasive cleaners, abrasive pads, or wire brushes. These products may damage the textured black powder coat finish. Use only mild automotive detergent for cleaning and non-abrasive wax or polish for protection and finish restoration.
Use a level to check that the bumper is level. Adjust if necessary before fully tightening all hardware. The manual also instructs to check that bumper corners match up when side extensions are loosely installed, adjusting if necessary before final tightening.
The manual confirms TrailChaser™ bumpers fit Jeep vehicles, with specific vacuum pump relocation required for 2012 models and later. For exact year and model compatibility, contact ARIES Automotive at 877-287-8634.
Required tools: ratchet, socket set, socket extension, box wrench set, Phillips and flathead screwdrivers, Allen wrench set, cut-off tool, and level. Specific sockets needed: 18mm (factory bumper removal), 16mm (side extensions and guards), 10mm (vacuum pump), 7mm (fog lights).
Yes, at least one additional person is recommended to help lift the bumper into place during installation.
M6 bolt = 7 ft-lbs, M8 bolt = 16 ft-lbs, M10 bolt = 33 ft-lbs, M12 bolt = 58 ft-lbs. Use these unless otherwise noted in the instructions.
Wax after installation and regularly thereafter. Use only mild automotive detergent for cleaning. Do not use abrasive cleaners, wax, pads, or wire brushes. Perform periodic inspections to ensure all mounting hardware remains tight.
LED lights are included only with kits using corner side extensions (2081205 aluminum or 2081200 steel). Kits with side extension style or corner style 2081207/2081206 do not include LEDs. Check your kit number on pages 2–3.
On Sale Today
Original price was $845.95. Current price is $480.00.You save $365.95 (43%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
Shipping from Lancaster, TXFREE SHIPPING
Estimated delivery Fri, Aug 14 - Sun, Aug 16
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.
