Our in-house experts typically reply within one business day.
Luverne
Verify Fitment
Select your vehicle to confirm this part fits.
2007 - 2009 Dodge Sprinter 2500
Confirmed to Fit
2007 - 2009 Dodge Sprinter 3500
Confirmed to Fit
2007 - 2021 Freightliner Sprinter 2500
Confirmed to Fit
2007 - 2021 Freightliner Sprinter 3500
Confirmed to Fit
2010 - 2026 Mercedes-Benz Sprinter 2500
Confirmed to Fit
2010 - 2026 Mercedes-Benz Sprinter 3500
Confirmed to Fit
Always the correct part
We know our products
Quality Products
Free Shipping!
Always the correct part
We know our products
Quality Products
Free Shipping!
Like many LUVERNE side steps and running boards, O-Mega II 6" oval side steps are made to work hard and to do it with style. They are constructed from strong, lightweight, rust-free aluminum, and to truly make them a step up from the rest, we shield them in a highly durable powder coat finish. This ensures maximum corrosion resistance and excellent protection against scuffs and scratches. The side steps are available in two powder coat finish options, including textured black and silver powder coat. O-Mega II side steps are also made to provide safe, comfortable entry and exit from your vehicle. They feature tough aluminum step pads with protruded circular treads that will never wear or crack. The step pads offer a non-skid surface, and they are finished with a textured black powder coat for lasting corrosion resistance. Also unique to our O-Mega II step pads is their customizable positioning. The pads are packaged unattached from the tubes and mount with self-tapping screws. This allows you to precisely match the layout of your vehicle to suit your preferences. You can mount them to the provided factory specifications or adjust them to a custom placement. The 6" x 2-3/4" tubes are fitted with black TPO plastic end caps, adding a modern, professional look. The end caps are also paintable to allow for even further customization. Each set of O-Mega II side steps is designed for vehicle-specific installation and fitment, using a unique set of mounting brackets. This particular set of side steps fits specific years of the Dodge Sprinter 2500 or 3500, Freightliner Sprinter 2500 or 3500 and Mercedes-Benz Sprinter 2500 or 3500 (see application info to verify fitment). NOTE: Mounting brackets are included but ship separately.
LUVERNE O-Mega II 6" oval side steps are made to work hard and to do it with style. They are constructed from strong, lightweight, rust-free aluminum and shielded in a highly durable powder coat finish of textured black or smooth silver.
LUVERNE has manufactured truck accessories in the United States since 1963, specialising in grille guards, running boards, side steps and mud guards for pickups, commercial vans and SUVs. Products are built primarily from stainless steel, aluminium and mild steel, with model-specific mounting kits that use existing frame locations for a bolt-on installation.
LUVERNE has been manufacturing automotive accessories in the United States since 1963, and six decades of continuous production have made it a nationally recognised name in the truck accessory market. Now a Lippert brand, it concentrates on a defined set of products rather than spreading across the whole aftermarket: front-end protection, step access and spray protection for pickup trucks, commercial vans and sport utility vehicles.
Step products are the largest part of the catalog and the range is unusually deep, because the right step depends on the vehicle's ride height, the width of the rocker panel and how often people get in and out. The O-Mega II six-inch oval steps give a wide, flat standing surface in polished stainless or black powder coat, while the Regal 7 seven-inch oval steps go wider still for full-size crew cabs and lifted trucks. The broader running board and side bar range covers round tube, oval and boxed profiles across cab configurations, with treads positioned at the door openings where they are used.
Grille guards protect the front end against impacts, brush and road debris, built in tubular stainless or steel with model-specific brackets that tie into factory frame mounting points. Because the fit is engineered per vehicle, installation is a bolt-on job that does not require drilling or cutting on most applications.
Rounding out the line, LUVERNE mud guards and mud flaps shield rocker panels, paint and following vehicles from stones and road spray, in widths matched to the tyre and fender they sit behind. Material choice runs through everything the brand does: stainless steel where appearance and corrosion resistance matter most, aluminium where weight is the priority, and mild steel with protective coating where strength and value lead. Customers include contractors, fleet operators, van upfitters and truck owners.
Experts available to answer your questions
Call 888-634-9494Limited Lifetime Warranty (Five-Year Finish, One-Year Parts)
6 compatible vehicles
| Year | Make & Model | Notes |
|---|---|---|
| 2007 - 2009 | Dodge Sprinter 2500 | — |
| 2007 - 2009 | Dodge Sprinter 3500 | — |
| 2007 - 2021 | Freightliner Sprinter 2500 | — |
| 2007 - 2021 | Freightliner Sprinter 3500 | — |
| 2010 - 2026 | Mercedes-Benz Sprinter 2500 | — |
| 2010 - 2026 | Mercedes-Benz Sprinter 3500 | — |
The O-MEGA II 6" oval steps are available as Model 583100 or Model 584100. Both models use the same installation process and are available in silver or black finish.
The O-MEGA II steps are listed as a universal application, but they require a specific bracket package for your vehicle. You must follow the instructions included with the bracket package you are using to mount the brackets to your vehicle. The manual does not specify which vehicles are compatible.
The 570744 bracket package is specifically designed for 2007-newer Sprinter vans only. It is not a universal application. The installation instructions are unique to Sprinter vans and involve drilling into the rocker panel and pinch weld.
The O-MEGA II step assembly includes: (1) aluminum extrusion in either 33" or 95" length in silver or black, (4) step pads, (4) plastic end caps, (18) square head screws 5/16-18 x 1", (18) serrated flange nuts 5/16-18, and (24) tek screws #8-18 x 1/2". Verify all parts are on hand before starting installation.
The 570744 bracket package for 2007-newer Sprinter vans includes: (4) mounting brackets, (3) additional mounting brackets for passenger side, (7) spacer brackets, (7) retainer plates, (5) U-nuts 5/16-18, (3) self-tapping screws 5/16 x 1.00, (14) hex head cap screws 5/16-18 x 1.00, (14) washers 5/16, (14) flange nuts 5/16-18, and (12) hex head screws 5/16-18 x 1.00. Verify all parts are on hand before starting installation.
The manual does not specify which tools are required for O-MEGA II step installation. You will need a drill to create 1/8" pilot holes for the step pad attachment and tools to tighten fasteners to the specified torque values (5 lb ft for end caps, 19 lb ft for flange nuts). Consult the bracket package instructions for additional tools needed for bracket installation.
You will need: a drill with 7/16", 7/32", and 11/32" drill bits; a center punch; a torque wrench; and hand tools for tightening fasteners. A scraper is needed to remove undercoating from the rocker panel before drilling.
The manual does not mention disconnecting the battery for O-MEGA II step installation.
The manual does not mention disconnecting the battery for 570744 bracket installation on Sprinter vans.
Yes. The manual explicitly states: "READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON THE SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION." Verify all parts are present before beginning work.
Yes. The manual explicitly states: "READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION." Verify all parts are present before beginning work.
The assembly order is: (1) Attach step pads to step plates using 1/8" pilot holes and 8-18 x 1/2" tek screws (5 screws per pad); (2) Install square head bolts into the designated slots in the bottom of the step plates; (3) Install end caps and tighten nuts to 5 lb ft; (4) Position the step on mounting brackets with square head screws in bracket slots, centered front to rear; (5) Install 5/16" serrated flange nuts on square head screws and tighten to 19 lb ft.
Place the step pads (Item #3) on top of the step plates. Using the holes in the step pad as a guide, drill 5 pilot holes of 1/8" diameter. Attach the pads with 5 tek screws (Item #7, 8-18 x 1/2") provided. Repeat for all step pads. This must be done before attaching the steps to the brackets.
Install the end caps (Item #4) as shown in Figure 1, tightening the nuts to 5 lb ft. The manual references Figure 1 for the correct positioning, which is shown on page 2 of the O-MEGA II instructions.
Position the step so that the square head screws (Item #5) are located in the slots of the mounting brackets and the step is centered front to rear on the vehicle. Install 5/16" serrated flange nuts (Item #6) on the square head screws and tighten to 19 lb ft.
The order is: (1) Preassemble brackets with spacer brackets using 5/16-18 bolts, washers, and flange nuts (finger tighten only); (2) Attach the front bracket by drilling a 7/16" hole 1/2" in front of the body plug (if no rear A/C) or drilling a 7/32" hole and installing a self-tapping screw (if rear A/C present); (3) Drill two 11/32" holes in the lower bracket mount using the bracket as a guide; (4) Fasten the bracket to the pinch weld with bolts, washers, and flange nuts; (5) Repeat steps 2-4 for the rear bracket, measuring 27 1/2" back from the front of the mud flap.
The order is: (1) Preassemble brackets with spacer brackets using 5/16-18 bolts, washers, and flange nuts (finger tighten only); (2) Install the front two brackets using the same process as the driver's side (steps 2-3); (3) Install rear brackets at three locations (48-1/2", 68-1/2", and 88-1/2" back from the front of the mud flap) using body plugs and U-nuts, drilling 11/32" holes in the pinch weld and fastening with bolts, washers, and flange nuts; (4) Attach the step assembly following the step assembly instructions.
Preassemble the main brackets (Item 1 for driver's side, Items 1 and 3 for passenger side) with spacer brackets (Item 8) using 5/16-18 bolts (Item 10), 5/16" washers (Item 2), and flange nuts (Item 11). Finger tighten only at this stage; do not fully tighten until the brackets are positioned on the vehicle.
Yes, drilling is required. You must drill 5 pilot holes of 1/8" diameter in the step plates to attach the step pads using tek screws. The bracket package may require additional drilling; consult the specific bracket package instructions for your vehicle.
Yes, extensive drilling is required. You must drill: a 7/16" hole 1/2" in front of the body plug (driver's side rear bracket, if no rear A/C); a 7/32" hole for the self-tapping screw (if rear A/C present); and two 11/32" holes in the pinch weld for each bracket. On the passenger side, you must drill 7/32" holes at three body plug locations (48-1/2", 68-1/2", and 88-1/2" back from the mud flap) and 11/32" holes in the pinch weld for each bracket.
Yes. The manual states: "SCRAP AWAY THE UNDER COATING" before removing body plugs and drilling holes on the rocker panel. This applies to both driver's side and passenger side installations.
If the truck does NOT have rear A/C: scrape undercoating, remove the body plug, drill a 7/16" hole 1/2" in front of the body plug hole, and insert a 5/16-18 U-nut. If the truck DOES have rear A/C: do not remove the body plug; instead, mark the hole location using the center round hole in the bracket as a guide, center punch, drill with a 7/32" drill, and install a 1/4" self-tapping screw.
The end cap nuts (Item #4) must be tightened to 5 lb ft.
The 5/16" serrated flange nuts (Item #6) that secure the square head screws to the mounting brackets must be tightened to 19 lb ft.
The pilot holes for attaching the step pads to the step plates are 1/8" diameter. Five pilot holes are required per step pad.
The tek screws are 8-18 x 1/2" (Item #7). Five screws are required per step pad.
The square head screws are 5/16-18 x 1" (Item #5). There are 18 screws included in the assembly.
The serrated flange nuts are 5/16-18 (Item #6). There are 18 nuts included in the assembly.
The O-MEGA II step extrusions are available in two lengths: 33.00" (Item #1 in silver, Item #1 in black) and 95.00" (Item #2 in silver, Item #2 in black). The manual does not provide width, height, or weight capacity specifications.
The 5/16-18 bolts used to preassemble the brackets with spacer brackets should be finger tightened only at the preassembly stage. The manual does not specify a final torque value for these bolts.
You will need drill bits in the following sizes: 7/16" (for U-nut hole on driver's side rear bracket without rear A/C), 7/32" (for self-tapping screw hole with rear A/C, and for body plug holes on passenger side), and 11/32" (for pinch weld holes on both sides).
The U-nuts are 5/16-18 (Item #4). Five U-nuts are included in the bracket package.
The self-tapping screws are 5/16 x 1.00" (Item #5). Three screws are included in the bracket package.
Front bracket: measure 9-1/2" back from the front of the mud flap on the back side of the rocker panel. Rear bracket: measure 27 1/2" back from the front of the mud flap. The height of the first bracket should be measured from the top of the bracket to the bottom of the floor board to help mount the rear bracket level.
Front brackets: use the same measurements as the driver's side (9-1/2" and 27 1/2" back from the front of the mud flap). Rear brackets: measure 48-1/2", 68-1/2", and 88-1/2" back from the front of the mud flap. Body plugs are located at these rear positions.
The O-MEGA II is a universal application, but requires a specific bracket package for your vehicle. Check the bracket package instructions to confirm fitment. The 570744 bracket package is specifically for 2007-newer Sprinter vans only.
You will need a drill with a 1/8" bit to attach step pads, a torque wrench, and hand tools. For Sprinter vans (570744), you also need 7/16", 7/32", and 11/32" drill bits, a center punch, and a scraper to remove undercoating.
Yes. The manual states: "BEFORE ATTACHING THE O-MEGA STEPS TO THE BRACKETS, PLACE THE STEP PADS (ITEM #3) ON TOP OF THE STEP PLATES ACCORDINGLY FOR YOUR VEHICLE." Attach pads with 1/8" pilot holes and tek screws before mounting to brackets.
End cap nuts: 5 lb ft. Serrated flange nuts securing the step to brackets: 19 lb ft.
Yes. The manual explicitly states: "READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON THE SERVICE PARTS LIST) ARE ON HAND BEFORE STARTING THE INSTALLATION."
On Sale Today
Original price was $584.95. Current price is $512.95.You save $72.00 (12%)
Free Shipping
Ships free on all orders
Authorized Dealer
Quick Ship
In stock and ready to ship — order now!
FREE ShippingFREE SHIPPING
Estimated delivery Tue, Aug 25 - Fri, Aug 28
Order before 2 PM EST Monday–Friday for same-day processing
Guaranteed safe & secure checkout
No reviews have been added for this product.
